logo

CO2 Power Pathways: Turbine, Hydraulic, Piston and Ferrofluid, and the Supermotive Free-Piston Engine

CO₂ Power Pathways: Which Is Most Efficient, and What a Combined "Supermotive" Engine Would Look Like

Turbine-generator vs turbine-hydraulic vs heated-piston hydraulic vs CO₂-entrained ferrofluid  ·  Infinity Turbine LLC  ·  November 2026

1. Summary

The CO₂ thermodynamic cycle sets the ceiling, and each extra conversion step after the expander removes a few percent. For electricity, a CO₂ turbine directly driving a high-speed generator is the most efficient route wherever the scale supports a good turbine (roughly 100 kW and up, and especially multi-MW sCO₂ Brayton at 500–700 °C, where cycle efficiencies reach 40–50%). When the output you need is hydraulic force, especially at small scale (10–200 kW) and low speed, a CO₂ piston expander driving hydraulic fluid directly is the most efficient route. It skips the generator and pump stages and suits the high pressure ratios and low flow rates where small turbines perform poorly.

Spinning a turbine to make hydraulic pressure only makes sense when hydraulic output is the end use. CO₂-entrained ferrofluid is the least efficient by a wide margin, below 1% heat-to-work. Its magnetic forces are about 1,000× weaker than hydraulic pressure, and CO₂ attacks the fluid's chemistry.

The best combined design is a double-acting free-piston CO₂ expander. Its rod carries a permanent-magnet section inside copper coils, which form a linear alternator and motor, and ends in a hydraulic plunger. Ferrofluid serves as rod seals and gap coolant, and MR fluid as the stroke damper. It does not beat thermodynamics. Its advantage is that it eliminates the crankshaft, gearbox, rotary generator and separate pump, and delivers electricity, hydraulic power or both from one moving part.

2. The four CO₂ pathways

PathDescriptionConversion chain
A Turbine → generatorCO₂ expands through a radial, axial or Tesla turbine on the same shaft as a high-speed PM generator. Power electronics condition the output.Heat → CO₂ → turbine shaft → generator → electricity
B Turbine → hydraulicThe turbine drives a hydraulic pump, through a gearbox if speeds don't match. Oil pressure drives cylinders or a hydraulic motor.Heat → CO₂ → turbine → (gearbox) → pump → oil → motor or cylinder
C Heated CO₂ piston → hydraulic cylinderHigh-pressure CO₂ from an external heater is admitted to a piston expander. The piston acts directly on a hydraulic plunger, with no crank. A batch variant heats CO₂ inside the cylinder itself.Heat → CO₂ → piston → oil (direct) → cylinder or motor
D CO₂ entrained in ferrofluidCO₂ dissolved or bubbled in a ferrofluid is heated to release and expand it, pressurizing the liquid. Optionally a magnetic field pumps it (thermomagnetic effect), or the moving fluid passes through coils.Heat → CO₂ desorption/expansion and ferrofluid magnetization → liquid pressure → (coil EMF)

3. Efficiency analysis

3.1 Downstream conversion chain (what survives after the CO₂ expands)

Each figure below multiplies typical component efficiencies. It shows how much of the ideal CO₂ expansion work reaches the useful output.

A turbine 0.60–0.88 × generator 0.95–0.97 × power electronics 0.96–0.98  = 0.55–0.84 electric
B turbine 0.60–0.88 × gearbox 0.97 × pump 0.90–0.93 × lines/valves 0.90–0.95 × cylinder 0.95  = 0.45–0.70 hydraulic  (→ electric via hyd. motor + generator: 0.38–0.60)
C piston expander 0.65–0.82 × direct oil transfer 0.90–0.95  = 0.59–0.78 hydraulic  (→ electric via hyd. motor + generator: 0.50–0.66)
D desorption/thermomagnetic conversion ≪ 0.05  = <0.05  (coil EMF from ferrofluid adds further loss)
S free-piston expander 0.70–0.84 × linear alternator 0.90–0.94 × electronics 0.97  = 0.61–0.77 electric, or 0.63–0.80 hydraulic via the plunger

3.2 Heat-to-output, indicative ranges

PathLarge scale (>5 MW, 550–700 °C, sCO₂ Brayton)Small scale (50–150 kW, ~250 °C, transcritical Rankine)Low grade (≤110 °C, transcritical Rankine)Output type
A Turbine → generator40–50%10–15%5–8%Electricity
B Turbine → hydraulic32–42% (rarely used)8–13%4–6%Hydraulic
C Piston → hydraulic (external heater, recuperated)Not practical (flow too large)11–15%5–8%Hydraulic
C′ Piston, batch-heated in cylinder—3–6%1–3%Hydraulic
D CO₂-entrained ferrofluid—<1%<0.5%Liquid pressure, µW–W electric
S Supermotive free-pistonNot practical11–15% (electric or hydraulic)5–8%Both

Ranges are net of CO₂ pump work and use realistic heat-exchanger approach temperatures and recuperation. Carnot limits for reference: about 65% at 650 °C, about 45% at 250 °C, about 26% at 110 °C (sink at 10–15 °C). Use these for screening only. Design numbers need a cycle model with real fluid properties (e.g., REFPROP/CoolProp).

3.3 Visual ranking: small scale (~250 °C, 50–150 kW)

C Piston → hydraulic (direct)
11–15%
S Supermotive free-piston
11–15%
A Turbine → generator
10–15%
B Turbine → hydraulic
8–13%
C′ Piston, batch-heated
3–6%
D CO₂ in ferrofluid
<1%

Scale: 0–25% heat-to-output.

3.4 Verdict

1Large scale, electricity: A sCO₂ turbine with a direct high-speed generator. No other path comes close at MW scale and high temperature.

1Small scale, hydraulic output: C piston expander driving oil directly. It needs an external heater, a recuperator, timed inlet valves and a crankless free piston. This is the best match for a remote wood-fired system whose job is hydraulic work.

2Small scale, electricity: A and S are close. Low-cost turbines (e.g., 1,800–3,600 rpm direct-drive) are simpler. A free-piston linear alternator wins where pressure ratios are high and flows small.

3B is worthwhile only when hydraulic output is the end goal and a turbine already exists.

4D is a research curiosity, not a power path (see Section 4).

Why piston expanders win at small scale: Transcritical CO₂ runs at roughly 60–140 bar with pressure ratios of 2–3 and very small volumetric flow because the fluid is dense. A small turbine then needs tiny blades at very high rpm, where tip leakage and friction dominate. A positive-displacement piston handles high pressure and low flow well at low speed, and couples naturally to hydraulic fluid, which is also a high-pressure, low-flow medium.
Batch heating is a trap: Heating CO₂ inside the working cylinder and then cooling it again means cycling the cylinder's metal mass every stroke. This makes it slow, adds large heat losses and leaves no room for a recuperator, which costs 50–70% of the possible output. Heat CO₂ in a separate heat exchanger, admit it through valves and recuperate the exhaust.

4. CO₂-entrained ferrofluid: a hard look

IssueDetailConsequence
Weak magnetic forceFerrofluid saturation magnetization is about 30–90 kA/m, giving magnetic pressure of about 1–10 kPa. Hydraulic oil runs at 20–40 MPa and CO₂ at 6–14 MPa.The magnetic contribution is about 1/1,000 to 1/10,000 of the CO₂ or hydraulic pressure, so it adds essentially nothing to power.
Coils around flowing ferrofluidFlux from a ferrofluid slug is about μ₀M ≈ 0.04–0.1 T, vs 1.2–1.4 T for NdFeB. Induced power scales roughly with B².About 150–1,000× less power per unit volume than a magnet-piston linear alternator. Entrained gas bubbles dilute it further.
CO₂ chemistryPressurized and supercritical CO₂ dissolves in or extracts hydrocarbon and ester carrier oils and is highly soluble in fluorocarbons. In water carriers it forms carbonic acid, which attacks magnetite.Swelling, foaming on depressurization, surfactant stripping, particle clumping and loss of the colloid.
Thermomagnetic pumpingWorks by magnetization falling as temperature approaches the particle Curie point (magnetite is about 585 °C, so only a small change across practical ΔT).Heat-to-work efficiency well under 1%. Useful only for no-moving-part circulation at very low head.
Gas-in-liquid expansionReleasing dissolved CO₂ by heating does pressurize a liquid, but it is an unrecuperated batch process.Behaves like batch heating (C′) with even worse heat transfer and slower dynamics.
Where ferrofluid does earn a place: as magnetic liquid seals on the moving rod at low-pressure boundaries, as a coolant in the alternator air gap, and as a small no-moving-part circulator for cooling loops. Its relative MR fluid is useful as an electronically controlled end-of-stroke damper and brake. Use solid permanent magnets for the electricity-making part.

5. The Supermotive Free-Piston CO₂ Engine (combined concept)

This concept puts all three motion types on one moving rod: linear CO₂ expansion, electromagnetic conversion (coils around a magnet section, the rotary motor's principle unrolled into a line) and hydraulic force. Magnetic fluids act as enablers.

Supermotive free-piston engine: section view (schematic) Hot CO₂ Hot CO₂ ① Double-acting CO₂ expander (valved) inlet valves ← heater/recuperator FF seal ② Linear alternator / motor (magnets + Cu coils) ferrofluid-cooled air gap FF seal MR damper ③ Hydraulic plunger (double-acting) Accumulator ⚡ Electricity (and motoring for start/stroke control) Hydraulic power Closed transcritical CO₂ loop CO₂ pump (driven by the engine's own hydraulics) → recuperator → heater (wood / waste heat / solar) → expander → recuperator → condenser → receiver

5.1 Components and what each does

ElementFunctionMotion typeDesign notes
① Double-acting CO₂ expanderHot, high-pressure CO₂ is admitted alternately to each side of the piston through timed valves, expands, then exhausts to the recuperator.Linear (thermal)Electronically timed solenoid or rotary valves set the cutoff, the expansion ratio being matched to load. Piston rings or clearance seal plus a buffer zone. Hot end isolated thermally from the magnets.
② Linear alternator / motorA NdFeB or SmCo magnet section on the rod moves inside copper coils to generate electricity. The same coils act as a linear motor to start, centre and control the stroke, replacing the crank and flywheel.ElectromagneticKeep magnets below their temperature limit (NdFeB about 80–150 °C; SmCo to about 300 °C). Proven in free-piston Stirling engines, where alternators reach 90%+ efficiency. An active rectifier/inverter controls stroke frequency and amplitude.
③ Hydraulic plungerThe rod end pumps oil into an accumulator. Valves set the split between electrical and hydraulic output, or switch to hydraulic only.Hydraulic (linear)Area ratio between CO₂ piston and plunger sets pressure intensification (e.g., 100 bar CO₂ → 250–300 bar oil). The accumulator smooths pulses. Can drive the CO₂ feed pump directly.
Ferrofluid sealsZero-leak, low-friction magnetic liquid seals on the rod between sections.Magnetic fluidOnly at low-pressure boundaries (about 0.2–0.3 bar per stage). The main CO₂ pressure is held by rings or labyrinths, with ferrofluid as the final buffer. Choose a carrier fluid for CO₂ compatibility and test it.
Ferrofluid gap coolantFills the alternator air gap to carry coil heat to the housing and slightly increase flux.Magnetic fluidStatic fluid with no CO₂ contact. Proven in loudspeakers.
MR fluid damperElectronically controlled end-of-stroke cushion and emergency brake if load is lost.Semi-magnetic fluidResponds in 5–20 ms. Prevents piston over-travel, which is the main failure mode of free-piston machines.

5.2 Why this combination makes sense

5.3 Main engineering risks

RiskMitigation
Stroke control (no crank sets the stroke limits)Closed-loop coil force control, position sensing, MR end dampers and a hydraulic end cushion.
Magnet temperatureTandem layout with the hot cylinder separated from the alternator, a cooled rod section, SmCo magnets, and ferrofluid gap cooling.
CO₂ blow-by and sealing at 60–140 barStepped seals: rings, then labyrinth, then a vented buffer, then a ferrofluid final seal. Return blow-by to the condenser side.
Valve losses and timingLarge-area fast valves, cam-less electronic actuation, and inlet cutoff tuned to the expansion ratio.
Vibration from a single pistonOpposed twin pistons on one axis (mirror-image units) to balance the forces.
Power density vs turbinesAccept a larger size for lower cost and robustness at 10–200 kW. Scale up with modular clusters rather than larger units.

6. Worked example: 500,000 BTU/hr wood-fired heater (~146 kW thermal)

PathHeat-to-outputNet outputComment
A Turbine → generator10–15%15–22 kWeTurbine efficiency at this size is the limiting factor.
B Turbine → hydraulic8–13%12–19 kW hydraulicExtra pump stage. Gearbox if turbine speed is high.
C Piston → hydraulic (direct)11–15%16–22 kW hydraulicBest for hydraulic-only duty.
C′ Batch-heated piston3–6%4–9 kW hydraulicAvoid.
D CO₂ in ferrofluid<1%<1.5 kWNot viable.
S Supermotive free-piston11–15%16–22 kW (any mix of electric and hydraulic)Same efficiency as C, plus electricity and self-starting.

Assumes CO₂ heated to about 220–260 °C by the flue-gas/thermal-oil loop, cooling water at about 10–15 °C, recuperation, and net of CO₂ pump work. Wood boiler efficiency (typically 65–80%) is not included. Multiply by it for fuel-to-output figures.

CONTACT Email: greg@infinityturbine.com | AMP