Infinity Turbine LLC


Publication Title | Introducing the LINK 2000 Integrated Battery Monitoring and Inverter Control

Organic Rankine Cycle

Waste Heat to Power ORC search was updated real-time via Filemaker on:

Waste Heat to Power ORC | Return to Search List

Search Completed | Title | Introducing the LINK 2000 Integrated Battery Monitoring and Inverter Control
Original File Name Searched: HP40.PDF | Google It | Yahoo | Bing



Page Number: 001
Previous Page View | Next Page View

Text | Introducing the LINK 2000 Integrated Battery Monitoring and Inverter Control | 001



Introducing the LINK 2000 Integrated Battery Monitoring and Inverter Control

QUESTION: Can the LINK 2000 be used as a battery monitor only?

ANSWER: YES! The LINK 2000 monitors the battery and sources independently of the inverter. Consider it an “Inverter ready monitor/control system” compatible with the Freedon Series of U.L. listed Residential inverters.

Control

Green LED indicates on.

INVERTER may be turned On or Off independently from charger.

IDLE MODE sets load sensitivity while idling, expressed in Watts. Range = 0W, 4W, 6W, 15W.

CHARGER may be turned On or Off independently from inverter.

PWR SHARE sets the AC current limit at which the battery charge rate is reduced to avoid overloading limited AC sources. Expressed in Amps. Range = 10A, 15A, 20A, 30A, 50A

SET UP allows the selection of various functions and values.

Press for 5 seconds to enable Set Up. The Green LED will flash at 1 second intervals. Then press the function to be set up. The present value will be displayed. After 3 seconds, with the button pressed, the display will began scrolling. When the desired value appears, release the button.

Flashing Green LED indicates Set Up mode. The LED of the function being set up also flashes.

START EQUALIZE function of charger by pressing SET UP button for 5 seconds followed by simultaneously pressing the VOLTS and A hrs buttons.

Red CHARGE LED flashes when in equalize mode.

STATUS indicators for AC power and charge cycle state.

AC IN: Green LED on when AC is present.

CHARGE: Red LED on when charger is in bulk charge mode.

Flashes Red when charger is in Equalize mode.

ACCEPT: Orange LED on when charger is in Acceptance mode. FLOAT: Green LED on when charger is in Float mode.

Monitoring

Green LED indicates selection

Selects BATTERY #1. RESET A hrs to zero.

Selects BATTERY #2. TYPE # sets battery chemistry: 1=Liquid, 2=Gel

Green LED indicates parameter displayed. CHARGE EFFICIENCY FACTOR of selected battery displayed as percentage.

AMBIENT TEMP sets default Charging Voltage for selected temperature range. Default value = 70°F. Range 30–120°F in 10° increments

AMP-HOURS consumed from selected battery displayed as a negative number. Over-charge A hrs displayed as positive number.

BATT CAP sets battery capacity.

Default value = 200 Ahrs. Range 20–2000 Ahrs in 20 Ahr increments.

AMPS charging into the selected battery are displayed as a positive number. Discharge Amps displayed as a negative number. Range ± 500 Amps with 0.1A resolution below 27A and 1.0A resolution above 27A.

CHARGED % sets the current that the charge rate must fall below for the battery to be considered full. Default value = 2% of battery capacity, (Ex: 4 Amps = 200 X 2%). Range 1–7% in 1% increments.

VOLTAGE of selected battery is displayed. Range 8.5–50 Volts with 0.05V resolution.

CHARGED V sets the Voltage the battery must be above to be considered full. Default value = 13.2V or 26.4V Sets default automatically for 12V or 24V systems. Range 13–40V in 0.1V increments.

Compatible with

Heart Interface Inverter models: Freedom 10

Freedom 20

Freedom 25

The LINK 2000 is a joint venture of two Valley Forge companies:

811 1st Ave. S. Kent, WA 98032 (206) 859-0640

Mfg. by Cruising Equipment Co. 6315 Seaview Ave. NW Seattle, WA 98107 (206) 782-8100

Image | Introducing the LINK 2000 Integrated Battery Monitoring and Inverter Control



introducing-link-2000-integrated-battery-monitoring-and-inverter-control
Waste Heat to Power - ORC - - Waste Heat to Power System - Go to website

Search Engine Contact: greg@infinityturbine.com